EMS600 – Engine Management

$USD 380.0

$USD 380.0
Select delivery location

SKU: EMS600 Category:

Overview

Standalone engine management system based on Megasquirt MS3x processor and firmware with enhanced inputs and output ports in aluminum sealed enclosure and sealed automotive grade connector. It is capable of controlling sequential injection on engines up to 6 cylinders, or semi-sequential up to 12 cylinders, combined with direct fire ignition for engines up to 6 cylinders (active or passive coils) or wasted spark ignition on engines up to 12 cylinders (active only coils). Can be connected as a fully standalone ECU or as piggyback and share the sensor reading with the stock ECU as it has differential trigger inputs, The 4 bar internal MAP sensor can read up to 44psi of boost,  5V ref voltage, and software switches to pull up resistors.  It has dedicated inputs (Crank, CLT, IAT, MAP, TPS and O2), 2 programabble knocking input. 13 low side outputs to drive injectors or any solenoid valve, 4 of them can be used to drive stepper motor idle. 6 dedicated ignition outputs and to drive both active and passive coils, unused ignition output can be used as auxiliary output to drive any solenoid. 7 digital/frequency. 5 analog/digital inputs. It comes with a mating connector and terminals. CAN bus connectivity, SD card slot and Real Time Clock (RTC) with backup battery for data logging. USB as main connectivity and USB or WiFi for monitoring. BluetoothWifi name and pin are configurable.

Description

  • 2x programmable differential trigger inputs (HallVR).
  • 13x high impedance low side output  3A each to drive injectors or to be used for auxiliary outputs.
  • 4 auxiliary output can be used to drive stepper motor idle.
  • 6x ignition output generates high current to drive passive coils directly or generates 5V to drive active coils.
  • 5x inputs can be used as analog or digital (switch) input.
  • 6x digital inputs to be used for switching or to read frequency.
  • 4x dedicated analog input, coolant temperature, Intake air temperature,  O2 sensor, Throttle position.
  • 2x programmble knocking input.
  • 4 bar built in MAP sensor.
  • Fully compatible with MSextra Software
  • Fuel Table 16×16
  • Ignition Table 16×16
  • USB for PC communication.
  • CAN bus supported.
  • Mating connector and terminals.
  • BluetoothWiFi connectivity.
  • SD card logging (card not included).
  • Real Time Clock with backup battery (battery not included).
  • Can be connected as standalone or piggyback

Specifications

Fuel table size 16×16
Fuel table resolution 0.10%
rpm resolution 1 rpm
Accel enrichment Simple (TPS,MAP), Enhanced (wall-wetting)
Spark table size 16×16
Advance resolution (commanded) 0.1 deg
Injector phasing Bank/batch fire
 
Fully sequential (up to 8cyl)
 
 
Injector timing Timed for start, middle, end of injection pulse
Injector trim Mapped trim table per cylinder.
Spark trim Mapped trim table per cylinder
EDIS Y
Distributor spark Y
Trigger return dizzy Y
Simple wheel decoding Y
Every tooth wheel decoding Y
Wasted spark Y
Coil on plug Y
Dual dizzy Y
Cam / 2nd tach input Y
Number of spark outputs 8
Rotary trailing Y
HEI7, GMDIS Y (with bypass control)
TFI Y
Oddfire wheel decoder Y
Oddfire dizzy Y
Neon/420A Y
36-1+1 Y
36-2-2-2 Y
Subaru 6/7 Y
IAW Weber-Marelli Y
Mitsubushi 6g72 Y
4/1 CAS Y
4G63 (Miata) Y
99-00 Miata Y
Renix 44-2-2 Y
Twin trigger (aka. dual spark) Y
Suzuki Swift Y
Suzuki Vitara Y
Daihatsu 3 cyl Y
Daihatsu 4cyl Y
Rover K Series 36-1-1 Y
Rover K Series 36-1-1-1-1 Y
Rover K Series 36-2-2 Y
Honda VTR1000 12-3 Y
Chrysler 2.2/2.5 Y
GM 7X native Y
Nissan 360 tooth CAS SR20, RB25
Load methods SD, AN, map/baro (load%), MAF, ITB
Load blending Y
Load tables 2
Staged injection Y
 
Includes sequential staging and multiple banks.
Over-run fuel cut Y
Tachometer output Y
Launch Control/flat shift Y
Spark cut rev limit Y
Dwell duty% Y
Dwell battery correction table of %ages
Cranking pulsewidth table of %ages
Alternate cranking injection Y
Specific cranking advance, dwell Y
Fixed timing for setup Y
Test mode Pump, Inj, Coils, Idle
Closed loop idle control Y
Boost control Y (open or closed loop with PID control)
Nitrous control Y (2 stage progressive)
Knock sensor (software) Y
Realtime barometric correction Y
Water Injection Y
Table Switching Y
Configurable outputs Y
AFR target tables Y
Dual fuel tables (per bank) Y
Synchronous sensor sampling Y
CAN communications Y
Built in tooth/trigger loggers Y (tooth, trigger, composite, sync-errror)

Download

 
 

About the author

Leave a Reply

Your email address will not be published.