Standalone Engine Management SEM301 PCB Based on MS3x

$USD 305.0

Out of stock

SKU: sem301pcb Category:

Overview

Standalone engine management system based on Megasquirt MS3x Processor and firmware with enhanced inputs and output ports in sealed enclosure and sealed automotive connector. It is capable of controlling sequential injection on engines up to 8 cylinders, or semi-sequential up to 16 cylinders, combined with direct fire ignition for engines up to 8 cylinders or wasted spark ignition on engines up to 16 cylinders. Can be connected as fully standalone ECU or as piggyback and share the sensor reading with the stock ECU as it has differential trigger inputs, The 4 bar internal MAP sensor can read up to 44psi of boost, 2 Programmable knocking detector circuit can be used to adjust the ignition timing,  5V ref voltage, and internal switch to pull up resistor.  It has dedicated inputs (Crank, CAM, CLT, IAT, MAP, TPS, O2 and knocking) and 16 low side outputs to drive injectors or any solenoid valve. 4 dedicated ignition outputs and 4 ignition outputs shared with inputs. 9 digital inputs 5 of them can be used as analog or digital. Bluetooth as optional connectivity , SD card logging, Real time clock.

Description

  • 2x Deffrential Trigger inputs (Hall, VR and Opto).
  • 16x High impedance low side output  3A each to drive injectors or to be used for auxiliary outputs.
  • 8x Ignition output 1A max (5V or 12V)/ 4 of them shared with inputs
  • 5x Inputs can be used as analog or digital input.
  • 1x Digital inputs one of them differential.
  • 4x dedicated analog input, coolant temperature, Intake air temperature,  O2 sensor, Throttle position.
  • 2x Programmable knocking input ./ shared with analog input.
  • 4 bar built in MAP sensor.
  • Fully compatible with MSextra Software
  • Fuel Table 16×16
  • Ignition Table 16×16
  • Connected to computer through USB.
  • USB cable
  • Supports CAN Bus
  • Bluetooth connectivity.
  • SD card logging.
  • Real Time Clock with backup battery
  • Can be connected as standalone or piggyback

Specifications

Fuel table size 16×16
Fuel table resolution 0.10%
rpm resolution 1 rpm
Accel enrichment Simple (TPS,MAP), Enhanced (wall-wetting)
Spark table size 16×16
Advance resolution (commanded) 0.1 deg
Injector phasing Bank/batch fire
Fully sequential (up to 8cyl)
Injector timing Timed for start, middle, end of injection pulse
Injector trim Mapped trim table per cylinder.
Spark trim Mapped trim table per cylinder
EDIS Y
Distributor spark Y
Trigger return dizzy Y
Simple wheel decoding Y
Every tooth wheel decoding Y
Wasted spark Y
Coil on plug Y
Dual dizzy Y
Cam / 2nd tach input Y
Number of spark outputs 8
Rotary trailing Y
HEI7, GMDIS Y (with bypass control)
TFI Y
Oddfire wheel decoder Y
Oddfire dizzy Y
Neon/420A Y
36-1+1 Y
36-2-2-2 Y
Subaru 6/7 Y
IAW Weber-Marelli Y
Mitsubushi 6g72 Y
4/1 CAS Y
4G63 (Miata) Y
99-00 Miata Y
Renix 44-2-2 Y
Twin trigger (aka. dual spark) Y
Suzuki Swift Y
Suzuki Vitara Y
Daihatsu 3 cyl Y
Daihatsu 4cyl Y
Rover K Series 36-1-1 Y
Rover K Series 36-1-1-1-1 Y
Rover K Series 36-2-2 Y
Honda VTR1000 12-3 Y
Chrysler 2.2/2.5 Y
GM 7X native Y
Nissan 360 tooth CAS SR20, RB25
Load methods SD, AN, map/baro (load%), MAF, ITB
Load blending Y
Load tables 2
Staged injection Y
Includes sequential staging and multiple banks.
Over-run fuel cut Y
Tachometer output Y
Launch Control/flat shift Y
Spark cut rev limit Y
Dwell duty% Y
Dwell battery correction table of %ages
Cranking pulsewidth table of %ages
Alternate cranking injection Y
Specific cranking advance, dwell Y
Fixed timing for setup Y
Test mode Pump, Inj, Coils, Idle
Closed loop idle control Y
Boost control Y (open or closed loop with PID control)
Nitrous control Y (2 stage progressive)
Knock sensor (software) Y
Realtime barometric correction Y
Water Injection Y
Table Switching Y
Configurable outputs Y
AFR target tables Y
Dual fuel tables (per bank) Y
Synchronous sensor sampling Y
CAN communications Y
Built in tooth/trigger loggers Y (tooth, trigger, composite, sync-errror)

Download

About the author

Comments

  1. Hey, I am in the process of designing a pnp hat for sem301 for e36 BMW ms41 DME’s.
    Could i possible have the footprint of the board and the connector layout please.

    Regards,
    A Masood.

Leave a Reply

Your email address will not be published.

There once was a group of French stars in the adult film industry who pornocave.com were known for their hardcore pornography. They were some of the best in the firelard.com business, and their films quickly became some of the most popular and acclaimed in nudepornos.com the industry. But despite their success, the stars began to feud. They fought over who mylovedpantyhose.com was the best performer, who was making the best films, and who was getting iperfectgirls.com the most attention from fans and critics. Eventually, the feud turned into a battle for pornoschip.com control of the industry. The stars fought each other in public forums, in newspapers, bulbfuns.com and on television. But it was all for naught. The French stars were no match hi-fatty.com for the American porn industry, and they were eventually forced to retire from the